Tufted 2ft. x 2ft. Seamless Glue-up Wall Panel (Package of 12 Tiles), Plain White

(5 reviews) Write a Review
Model No.
2-3 weeks
30mm / 1.2 in.
48 sqft per pack
Pack Contains:
12 tiles
10lb (per pack)
High-Density EPS (foam)
310 Akfix / 2 tubes per pack
Yes (Acrylic paints)
Custom Finishing:
We can paint this tile with any acrylic paints of your choice. Please contact us for a custom quote.
23.5" x 23.5"
Plain White
Installation Method:
Glue-up (Instant Grab #310)
Return Policy:
Hand Painted Versions made to order, no returns. Made in Poland / Painted in USA. Consider ordering samples

How many tiles do I need?:

Ceiling / Wall Tile Project Estimator
* Enter your ceiling area of room
Length ft.&Width  ft.
or total area in square feet.
* Enter your ceiling tiles size
Minimum number of tiles needed
Tiles needed with 15% of waste
Minimum number of Instant Grab adhesive #310 (Caulk gun needed)
Note: It is important to add a 15% more tiles to this number for waste.
Enter your Email
Moldings Project Estimator
* Enter linear footage of room in
Length ft.&Width  ft.
or total area in linear feet.
* Type
Minimum units of Moldings needed
Coverage area ln. ft.
Moldings needed with 15% of waste
Note: It is important to add a 15% more moldings to this number for waste.
Enter your Email

Tufted 2ft. x 2ft. Seamless Glue-up Wall Panel (Package of 12 Tiles), Plain White 

EPS 3D Wall Panels - Installation Instructions

You will need the following to install the panels correctly:

  • A wallpaper cutter
  • A measure tape
  • A level
  • A pencil
  • A primer
  • An adhesive for polystyrene foam
  • An acrylic filler (optional)
  • Acrylic or latex paint (optional)
  • 1 mm (spax) decking spacers (optional)

Remove the panels from the packaging and wait for at least 4 (four) hours to allow the product to adapt to ambient temperature. Before installing the panels, place them on a flat surface to arrange them in a pattern and to inspect them for mechanical damage that may have been caused during transport. Once you install the panels on a wall or ceiling, you will not be entitled to make any warranty claims.

Step 1. Prepare the surface

The panels should be installed on a clean and dry surface free form loose dirt. Before installation, any holes in the surface (wall or ceiling) should be filled with a patching compound. If the surface is covered with wood, plastic or varnish, sand the surface matt with fine grit sandpaper.

Now prime the surface using a commercial primer.

Step 2. Arrange the panels

Before installing the panels, plan how to arrange them on the surface, paying attention to the direction of the pattern.

A rough drawing of the arrangement is recommended. Use a level and a pencil to mark the contours of the panels on the surface.

Step 3. Cutting

To cut the panels, use a wallpaper cutter. Measure the right length and cut it off with a precise movement.

Step 4. Install the panels on the wall

Glue the panels directly onto the wall using a multi-purpose adhesive for polystyrene foam. Apply the adhesive evenly onto the surface, either in spots or all along the edge of the panel, about 2 ‐ 3 cm from the edge (the reverse side of the panel), and on the contact edges of the panel. Now press the panel gently onto the surface. Use a damp cloth to remove any excess amount of the adhesive. When placing the panels onto the wall, make sure that all the edges adhere properly to the surface. If you discover any cracks in the joints on the panels, use an acrylic filler. As an option, you can install the panels using (spax) decking spacers, not thicker than 3 mm.

Apply an acrylic filler in all cracks. Apply an acrylic filler in all cracks and use a plastic putty knife to remove any excess amount of the filler material to give the surface a uniform decorative look.

Step 5. Painting

Before painting the panels, it is best to wait for at least 24 hours to allow the adhesive acrylic filler material to dry. using commercial acrylic or latex paints for indoor use, paint the panels twice.


  • Do not press the panels onto the wall too hard, as this may damage them.
  • Use only proven, high quality paints ‐ for good coverage.
  • Use an adhesive for polystyrene foam. Consider buying it from us, as we can help you choose the right adhesive for the products.
  • Remember to cut the panels only with a sharp wallpaper cutter.
  • After painting, use a feather duster or vacuum cleaner with a soft brush attachment to clean the panels.

Do not install the panels in busy areas. Choose surfaces away from an open flame and high temperatures (e.g. a fireplace, a gas cooker etc)

  • 5
    so beautiful wall panel

    Posted by lhatzaw on Jan 8th 2020

    I was amazed how beautiful those wall panel are.It was my first time using them and was surpirsed how easy was to use them even for the first time user,just need to read all instructions and then will be easy.It made work easier as it came with a glue included.Those tile are 48 sq.ft.I was so happy with results that i made in the bathroom cealing with those wall panel,looked beautiful and the bathroom looks so bright and bigger as the white color of wall panel gives you that.Those are the nieciest wall textures that i have ever saw it.Leigh tweight,perfectly square,easy to install and beautiful design.

  • 4

    Posted by Tess 61 on Dec 31st 2019

    I love these decorative tiles. With the holidays, I have not been able to complete my project, however the tiles are very beautiful.
    They are sturdy and will make a great addition as a decorative wall in my bathroom. I love the design and it looks like it will easily clean

  • 5
    Nice Panels

    Posted by acaine73 on Dec 30th 2019

    These panels are beautiful and makes my room look great. I did have one other person help me install them and it was very easy. We did not paint them, just installed them as is. They really add a nice, clean look to the room as well as dimension. These are great if you are looking to make a change to any room.

  • 5
    Makes a great accent wall

    Posted by njmcpike on Dec 26th 2019

    These are so easy to use and put up, just put some caulking glue on the back and stick on the wall. You can cut them to size or different shapes and there's even instructions on how to do it all. Going to paint them as soon as I figure out what color I want them to be. They are a styrofoam type, so be careful not to put anything heavy on them because it will show the dings and scratches.

  • 4
    Super light weight

    Posted by HandyMan55 on Dec 20th 2019

    These panels are super light weight and seem to take paint well. A few were broken when they arrived but I'll probably need to buy another batch to finish the project anyway. Lets see how they hold up over time.