Ocean 2ft. x 2ft. Seamless Glue-up Wall Panel (Package of 12 Tiles), Plain White
EPS 3D Wall Panels - Installation Instructions
You will need the following to install the panels correctly:
- A wallpaper cutter
- A measure tape
- A level
- A pencil
- A primer
- An adhesive for polystyrene foam
- An acrylic filler (optional)
- Acrylic or latex paint (optional)
- 1 mm (spax) decking spacers (optional)
Remove the panels from the packaging and wait for at least 4 (four) hours to allow the product to adapt to ambient temperature. Before installing the panels, place them on a flat surface to arrange them in a pattern and to inspect them for mechanical damage that may have been caused during transport. Once you install the panels on a wall or ceiling, you will not be entitled to make any warranty claims.
Step 1. Prepare the surface
The panels should be installed on a clean and dry surface free form loose dirt. Before installation, any holes in the surface (wall or ceiling) should be filled with a patching compound. If the surface is covered with wood, plastic or varnish, sand the surface matt with fine grit sandpaper.
Now prime the surface using a commercial primer.
Step 2. Arrange the panels
Before installing the panels, plan how to arrange them on the surface, paying attention to the direction of the pattern.
A rough drawing of the arrangement is recommended. Use a level and a pencil to mark the contours of the panels on the surface.
Step 3. Cutting
To cut the panels, use a wallpaper cutter. Measure the right length and cut it off with a precise movement.
Step 4. Install the panels on the wall
Glue the panels directly onto the wall using a multi-purpose adhesive for polystyrene foam. Apply the adhesive evenly onto the surface, either in spots or all along the edge of the panel, about 2 ‐ 3 cm from the edge (the reverse side of the panel), and on the contact edges of the panel. Now press the panel gently onto the surface. Use a damp cloth to remove any excess amount of the adhesive. When placing the panels onto the wall, make sure that all the edges adhere properly to the surface. If you discover any cracks in the joints on the panels, use an acrylic filler. As an option, you can install the panels using (spax) decking spacers, not thicker than 3 mm.
Apply an acrylic filler in all cracks. Apply an acrylic filler in all cracks and use a plastic putty knife to remove any excess amount of the filler material to give the surface a uniform decorative look.
Step 5. Painting
Before painting the panels, it is best to wait for at least 24 hours to allow the adhesive acrylic filler material to dry. using commercial acrylic or latex paints for indoor use, paint the panels twice.
NOTE!
- Do not press the panels onto the wall too hard, as this may damage them.
- Use only proven, high quality paints ‐ for good coverage.
- Use an adhesive for polystyrene foam. Consider buying it from us, as we can help you choose the right adhesive for the products.
- Remember to cut the panels only with a sharp wallpaper cutter.
- After painting, use a feather duster or vacuum cleaner with a soft brush attachment to clean the panels.
Do not install the panels in busy areas. Choose surfaces away from an open flame and high temperatures (e.g. a fireplace, a gas cooker etc
-
Perfect for my beach house!
I recently installed the Ocean tiles from La Maison as an accent wall, and they give the perfect beachy vibe!
I love that they are seamless and lightweight, making installation quick and easy with the glue tubes that were included.
I painted them a deep ocean blue and they look awesome! -
Interested Concept for Accent Wall
As an Interior Designer, I was curious about these wall tiles. Although I knew they were 24x24, the seamed huge when they came and were about an inch thick, so you'll want to make sure you have the wall depth to install them, not like a wallpaper or a traditional tile at all. Also, my shipment had absolutely no instructions so I guessed how to install them and most likely did it incorrectly as I'm not happy with the overall appearance. I am going to, however, try and camoflauge the seams and paint them when I have time and I'm guessing they will look 100% better
-
Easy Installation
Used the wall panels for an accent wall in my half bath. Install was a breeze, glue, stick, and done! The wall looks gorgeous, it made the room appear larger. The wall appears to be one solid wave, you can not see the seams. I will be doing my master bedroom next, highly recommend these to anyone looking to beautify their space.
-
Material not so great
I’ve been wanting to make our kitchen bar pop a bit more and thought this would be a perfect solution. However, the material is pretty much Styrofoam. If anyone were to lean up against it or slam a chair too hard under the bar counter it would damage easily. I really wanted to be able to use this as I can see why the material is what it is. It’s light so you can easily apply it to the wall. I obviously did not try painting the material. I would recommend using this on a wall that no one can touch. Also it would need to be a wall with nothing on it. No light switch or plugs as I don’t know how you could around the material and it look good since the material is 3D and sticks out from the surface at least a couple of inches.
-
Smooth molded foam tiles
Lightweight and easy to affix to the desired surface. These glue-up wall panel tiles are sturdy, yet add a touch of elegance to any room. The adhesive glides on and is very manageable to properly position. It was a breeze to make an accent wall in my bathroom. The design quality is stunning and the smooth molded finish is perfect as-is or a wonderful surface for painting. We noticed the added bonuses of dampening sound and increased insulation upon completion. I would highly recommend to those looking update in an efficient, yet beautiful manner. Very pleased with the panels and would use them again.
